新的家用电动石磨机通常不太可能出现问题，但是在长期使用后，一定要做好家用电动石磨机的日常维护和校准维护工作，下面来具体讲讲内容吧。

The new household electric stone mill is usually unlikely to have problems, but after long-term use, we must do a good job in the daily maintenance and calibration maintenance of household electric stone mill. Let's talk about the content in detail below.

经常检查轴承温度。如果温度过高，检查润滑和传动部件是否正常，滚动距离是否过紧。及时查明原因，采取相应措施，严重时停止检查。经常检查传动带的松紧度。皮带过松会降低传动效率，影响磨削效果。如果皮带过紧，容易造成轴承发热，增加动力消耗，降低传动皮带的使用寿命。

Check the bearing temperature frequently. If the temperature is too high, check whether the lubrication and transmission parts are normal and whether the rolling distance is too tight. Find out the causes in time, take corresponding measures, and stop the inspection when it is serious. Always check the tightness of the drive belt. Too loose belt will reduce the transmission efficiency and affect the grinding effect. If the belt is too tight, it is easy to cause bearing heating, increase power consumption and reduce the service life of the transmission belt.

各种传动部件必须紧固可靠，拆卸或安装应使用专用工具，严禁用手锤等工具直接敲打。不要忘记检查气动元件。经常检查气路中的气动元件，气路和连接处是否有漏气或损坏。同时检查供气压力是否符合要求，经常检查同步带的使用情况，如发现过紧、过松、跳动、跑偏、磨损严重等，应及时调整、修理或更换。

All transmission parts must be fastened and reliable. Special tools shall be used for disassembly or installation. It is strictly prohibited to knock directly with tools such as hand hammer. Don't forget to check the pneumatic components. Always check the pneumatic components in the air circuit, whether there is air leakage or damage at the air circuit and connection. At the same time, check whether the air supply pressure meets the requirements, and regularly check the use of the synchronous belt. If it is found to be too tight, too loose, jumping, deviation, serious wear, etc., it shall be adjusted, repaired or replaced in time.

定期、有序地更换磨粉机的磨辊，一次磨辊不宜更换过多。同时，磨辊的直径也不能相差太大。带齿滚子的角度、倾角和齿数应符合规定，并预留一定量齿顶平面。光辊各段锥度应准确并符合规定要求，表面粗糙度应均匀。更换磨辊后，用塞尺检查，根据各系统粉碎机的要求粗略调整滚动距离。

The grinding roller of the pulverizer shall be replaced regularly and orderly, and the primary grinding roller shall not be replaced too much. At the same time, the diameter of the grinding roller shall not differ too much. The angle, inclination and number of teeth of the toothed roller shall meet the requirements, and a certain amount of tooth top plane shall be reserved. The taper of each section of the smooth roller shall be accurate and meet the specified requirements, and the surface roughness shall be uniform. After replacing the grinding roller, check with a feeler gauge and roughly adjust the rolling distance according to the requirements of the crusher of each system.

每台机器的相应位置应有相应的工作规范、操作规程和简单的故障排除方法。制定所有设备台账，验证（校准）周期表和计划，并设置专人管理。正确使用和维护所有设备。具体维护和操作要点如下：

The corresponding position of each machine shall have corresponding working specifications, operating procedures and simple troubleshooting methods. Prepare all equipment accounts, verify (calibrate) periodic tables and plans, and assign special personnel to manage them. Properly use and maintain all equipment. Specific maintenance and operation points are as follows:

在日常维护和校准维护中，应密切关注影响检测结果的因素，如灰尘、温度、湿度、振动、噪音、腐蚀等因素，严格控制，减少误差。必须保证所有机器工作台面固定平整，符合使用要求。所有面粉机机器使用后应及时清洗和恢复，以保证下一次实验的顺利进行。

During routine maintenance and calibration maintenance, pay close attention to the factors affecting the test results, such as dust, temperature, humidity, vibration, noise, corrosion and other factors, and strictly control them to reduce errors. All machine worktops must be fixed and flat to meet the use requirements. All flour machines shall be cleaned and restored in time after use to ensure the smooth progress of the next experiment.

电气设备应安装与额定功率一致的独立电源开关，并有良好的接地线。个别石磨设备应按说明书要求配备稳压电源。使用机器的相关人员应学习相应的法律、法规和管理制度，所有操作人员均应取得资格证书或接受过机器操作培训。

The electrical equipment shall be equipped with independent power switch with the same rated power and good grounding wire. Individual stone grinding equipment shall be equipped with regulated power supply according to the requirements of the manual. Relevant personnel using the machine shall learn relevant laws, regulations and management systems, and all operators shall obtain professional qualification certificates or receive machine operation training.

总之，这些操作都是可以避免家用电动石磨机的磨损，有利于延长机器的使用寿命。更多相关内容的了解就来网站www.zysmcn.com进行咨询吧！

In short, these operations can avoid the wear of household electric stone mill and prolong the service life of the machine. For more information, please visit www.zysmcn.com Com for consultation!